Vinyl flooring usually has preserve its common presentation, such as single in rolls of large sheets, however time also has reward vinyl in matters of style and nowadays vinyl flooring is available in more practical, much easier to setting up formats.
At Finish Build vinyl flooring tiles are always recommended for commercial uses. Due to the lack of weight FinishBuild vinyl flooring products are usually purchased in 12-inch squares that feature adhesive backing. The thicker the tile is, the better it will hold up over longer periods of time, but what we really think it is important is the acoustic properties this material owns. Installing tile is an ideal project for DIY eagers, particularly in smaller rooms or in this case fashion shows ramp.
Nevertheless, it is important to purchase all tiles from the same lot because, while other lots may be labeled as being the same pattern and color, slight differences in shade may occur. When it comes about setting your chalk lines, starting in the center of the room is what we usually recommend. After removing paper backing, press tiles into place. Keep into account that trimming your tiles at the walls and other edges. Subsequently we suggest you to roll tiles in both directions to set them steady.
What FinishBuild recommends:
When it comes to installing vinyl planks, let me tell you is perfectly doable. Since vinyl flooring planks come with an easy interlocking system, you can easily jump on the journey of actually doing it yourself. At FinishBuild we are here, once again, with the purpose of helping you on do the first moves.
First of all let’s clean the room. Before starting, empty your room of all furniture and make sure that the surface of the room is perfectly smooth by removing nails, debris and scraping up any old adhesive. Take into account that your sub floor needs to be dry as well as be smooth and as even possible because every lump, bump and crease may appear visible. Make a template of the floor using felt paper.
Materials you would use:
- Tape measure
- Vinyl cutting knife
Once we have a clean surface, there is an important move you should definitely consider if you are aiming for outstanding results: Level your subfloor, generally vinyl planks flooring products can be install onto existed flooring surfaces. Therefore check the condition of your subfloor, if a surface is in poor conditions, you may need to substitute it. You can drill in a plywood underlayment with screws fairly easily, nevertheless it is important to screw heads below the surface of the wood. If you install an underlayment over your existing subfloor, make sure the surface is level. Afterwards, sealing is our next step. Paint a coat of sealant onto your subfloor. Protect the bottom of your walls or cabinets with strips of masking tape to avoid splash. Once the floor is sealed, let it cure for as long as required before you start laying your vinyl planks.
Now is time for you to make an important choice. Decide on which direction you will lay your vinyl planks. Subsequently, measure the floor to work out where the middle of your middle row will sit. This is your middle line. In order to be double extra sure, I personally suggest (and if you have the time) to face vinyl planks on the floor to get a clear idea of how can tiles adjust to the space. This also can help you to get a visual plus of the vinyl planks you might have to cut in order to fit edges. Next, hammer a nail at each end of this line and then tie a string chalk line between them. Snap your string chalk line to mark your center line on the floor.
Now proceed to set each plank by laying the first row of vinyl plank flooring, whether is by peeling them off on the back for each plank (in the case they are the adhesive type) or by assemble them if they come with the interlocking system. Subsequently flatten them it into place, over the top of the center line and remember that each vinyl plank has a directional arrow on its backing paper. At FinishBuild we strongly suggest that in order to obtain the finest visual result, lay all your planks facing the same way.
Lay the second row of vinyl plank flooring next to the first. Stagger the second row so the end of each plank lines up with the middle of the plank in the previous row. When laying the third row of planks, use your combination square to make sure its joins line up with the joins in the first row and try to maintain this staggered pattern going the whole way across the floor.
On this phase you must let go the extra vinyl material. Some of your vinyl floor planks will need to be trimmed to fit around the floor corners. Take into account that in phase 2 you can be aware of how much material is not going to be longer needed however, this phase allows you to measure and mark out your lines on each plank and make your cuts with a trimming knife. In order to get finest results, go over the cut line two or three times instead of trying to cut all at once. When your trim is finished, remove the backing paper and stick the plank in place hoping for the best. We recommend you (in case you have adhesive type) to curve and bend the board as you lay it down, visualize that when installing part of the vinyl plank would be against the floor while the part yet to be placed is in the air. Successively, roll the board down and onto the surface of your floor. The aim with this procedure is to avoid the development of air pockets, however you can also help yourself with a piece of fabric on your hand to press the boards to the ground.
To sum up, after installation, clean adhesive from tile surfaces with wet cloth. Fasten trim and moldings to the wall, not the flooring. In addition, avoid heavy traffic on the new installation for at least 72 hours while adhesive sets. If you are interest on see more about vinyl interlocking systems installation, we invite to check this video:
How To Install A Floating Vinyl Plank Floor
You start. We Finish!